Warrior

Warrior

Swingfire

ZT3A2

Warrior

Swingfire

ZT3A2

Britain

VI Rank

Battle rating:

AB	RB	SB
8.3	8.3	8.3

Class:

Light tank

Research:135 000

Purchase:380 000

Description

The Combat Vehicle, Personnel, Tracked, 30mm Gun, Warrior FV510 (or just the Warrior) is a Rank VI British light tank with a battle rating of 8.3 (AB/RB/SB). It was introduced in Update 1.81 "The Valkyries".

Warrior is basically a big box with a round turret, which has a little gun in middle, "ears" (ATGM cameras), and the ATGM launcher itself on the right side. Front of the hull is sloped to decrease small firearms damage. IFV hull is huge compared to even medium tanks of some factions (about double the size of T-62) and looks even bigger when carrying additional armour.

On its right front, there are exhaust ports, which are a weak spot in armour structure and may prevent gunner from firing precisely in Realistic Battles due to smoke and heat coming out of them, though usually, it's not a big problem.

If the vehicle has Add-on armour, it's easily identified for its riveted plates on sides of the vehicle. Usually, after being shot with a high velocity round, they break off. Plates do not protect the rear of the vehicle.

Practically, the Warrior is the only proper light tank the British faction has. It's mostly played as an aggressive ATGM tank or ambush scout tank, though it can fulfil any role that doesn't involve it being constantly shot at.

It's best described as a hybrid between a slowed down SPAA and assault ATGM launcher, while armour is either nonexistent or installed via a modification to partially protect from hazards that normally annihilate light tanks. The weapon combo is potent enough to destroy even modern MBT's, and with add-on armour, the Warrior can bully even heavy tanks in close range, though the turret is still very vulnerable.

The Warrior can be played defensively (mostly around hills and mountains), or aggressively (on flat terrains and in towns), given that there is enough cover for the Warrior. In realistic battles, Warrior can also hide relatively well and use either of its weapons to punish unsuspecting people, or just scout them.

This vehicle is very easy to play while still in stock mode, as it has most essentials available at stock or unlocked early on, however, every upgrade only makes it even stronger.

General info

Survivability and armour

This box outside of warrior can sometimes block APHE from leaving the vehicle. On top of that, chemical rounds can also hit it, or construction below it and cause the hull to break.

Warrior is well protected against heavy machine guns, however, it's a turret, engine ventilation, hull's back and even sides have weak spots, which can be penetrated by 12.7 mm and 14.5 mm HMG, if shot correctly. Frontal armour can sustain light automatic cannon fire. Anything of higher calibre has a high chance of destroying the light tank immediately at close range.

The Warrior can be hull-broken by any chemical shells of 105 mm calibre and kinetic shells of 120 mm calibre. Due to its huge and boxy profile, it often gets accidentally hit by ATGM's that were meant for other tanks nearby. Also, if artillery hit its hull or turret directly, it will instantly blow up entire tank.

It's important to remember, that hull itself is somewhat resistant to hull break, but the suspension, ventilation or track hit can instantly destroy the tank if done by any chemical explosives of any calibre. Heavy Explosives (HE) of high enough caliber instantly hull break the tank regardless of hit surface, destroying tank even if shockwave barely reaches any part of the tank.

Vehicles defences with and without add-on armour vary greatly:

Coaxial autocannons and low calibre SPAA penetrate turret and hull sides without add-on armour instantly. With add-on armour hull generally can sustain an attack for 1 to 5 seconds, depending on the angle of attack.

Due to armour being thick enough to protect from HMG, it will trigger fuse on any cannon shell in the game, unless it hits engine ventilation (which is extremely unlikely and bad on its own). As such, popular misconception of not using add-on armour to "increase the chance of over-penetration and move faster" should not be taken as a single truth. In fact, single APDSFS or APHE can annihilate Warrior easily by just scratching it, if it enters the vehicle at a bad angle.

Overall, add-on panels defend the sides and half of the front of the hull, with the frontal plate covering the driver. These panels protect from chemical ammunition and add a bit of an edge against kinetic ammunition. The side panels also hide obvious weak spots on the Warrior's hull (hatches), forcing an enemy to fire randomly. Side armour plates can block HESH and some weaker forms of chemical ammunition with about 130-160 mm of penetration power, the frontal plate can save from about 220 mm of chemical penetration power, saving the light tank from hull break. Unfortunately, since composite armour panel placement is not solid, sometimes shrapnel can penetrate stitches between them and destroy tracks, resulting in hull break.

As such, with Add-on armour, the Warrior can survive almost any machine gun fire, misplaced autocannon fire, close artillery miss, low-caliber SPAA fire, some chemical shells and the other things, that normally cause hull break or annihilate light tanks, so the Warrior can play much more boldly and harass enemy if they are alone.

In case of frontal panel somehow saving the vehicle from a frontal shot, but failed to completely nullify the attack, the Warrior will be very likely set on fire and have the engine broke, which may mean an impending knock-out if unable to retaliate, so keep that in mind. Keeping low ammo amount (about 30 out of 104 magazines) increases the chance of survival against HEAT shells after hull break prevention.

If 120 mm HE hits the frontal NERA plate, an explosion can still reach the turret and blast it off the tank, resulting in hull break. Avoid being hit by it at all costs.

The front-right side does not have complete armour protection because it's expected, that engine compartment takes the hit for the vehicle. In-game, it cannot prevent hull break, caused by explosives even touching the track, so try to face the enemy with the left side, if possible. Engine deck can prevent hull break from HEAT and, sometimes, HESH.

Protection analysis might get all weird with protection and damage values, but essentially frontal panel gives a 45% chance for the Warrior to not be destroyed from frontal HESH shot by just being there. Side armour does the same thing for the entirety of the sides but is weaker. Any shells of 120 mm calibre will likely obliterate Warrior from sides unless it was a grazing shot.

The side plates are not invulnerable, and so, after being hit too hard, they will break off, much like explosive reaction armour. The protection quality of these armour plates is most notable when compared to facing the BMP-2 (when it gets destroyed immediately) and the Begleitpanzer (when it actually saves the vehicle from grazing shots and only then falls off).

Any AP based shot, like APHE, will go through composite lists unless it was a grazing shot. Because of this, it's advised to avoid directly attacking SPAA with 30mm guns, and other IFV, as those can destroy the Warrior even without special APDS ammo, and have guns with a much higher rate of fire.

Here is the most unlikely and ridiculous example of add-on armour saving the Warrior's life. IT-1 ATGM has about 500 penetration power, which should destroy side armour of warrior at any angle, and even frontal plate with ease, however:

• 
• 
• 
• 

Since this particular edge of Armour plates is invulnerable, ATGM destroyed the entirety of Warrior Armour, but Warrior survived. As could be seen here, armour on warrior is extremely random. The sharper the angle of attack, the bigger the chance of miraculous survival.

Mobility

Game Mode	Max Speed (km/h)		Weight (tons)		Engine power (horsepower)		Power-to-weight ratio (hp/ton)
	Forward	Reverse	Stock	AoA	Stock	Upgraded	Stock	Upgraded
Arcade	89	89	24.9	1	852	1,049	34.22	40.5
Realistic	80	80			486	550	19.52	21.24

Mobility is adequate on vehicle's BR, it can move forward and backwards equally fast, but don't expect it to be climbing mountains like with the powerful Vickers MBT in Arcade Battles. It will just slide down if the surface is too steep.

In Arcade Battles, it's generally driving at 46-54 km/h offroad in either direction without engine upgrades, regardless of additional armour. With mobility upgrades it may drive up to 60 km/h, but not very often. Speed of 81-83 km/h can be reached if the Warrior drove off the hill and keep driving forward, or on completely flat terrains, like roads in the American desert, though sometimes it just doesn't work again at the same spot.

Due to its sheer size, it almost never gives in to ramming attempts, though it cannot move enemy heavy tanks either and shouldn't fight them on a narrow street.

Accidentally hitting something on max speed, especially explosive decorations, launches the Warrior up to 5 meters in the air, which is very entertaining, but almost never fazes the enemy.

• Adding armour does not decrease Warrior's hp/ton significantly, and it only reduces maximum climb angle by 2 degrees, so it should be used when unlocked without worries of mobility penalty.
• Despite having enough horsepower, this vehicle can not climb mountains.

Armaments

First of all, one needs to understand that both of the weapons on the Warrior are useful.

Main armament

The gun is very slow firing, but with APDS belt it can penetrate the sides of most medium tanks and SPGs. Basically, it's effective against medium tanks, but lacklustre against fast vehicles that have spaced armour. It can be used to hurt crew from over 1 km distance, but it's not very good at damaging enemy ammo racks, so it's best used to destroy engines, tracks and crew unless it's easier to hit.

Proper heavy tanks are normally not fazed by its fire at all, but for them there is the powerful MILAN launcher, which can penetrate them even from the front with its 580 mm penetration power, leaving them completely disabled.

In a perfect world, even in the worst situation, the Warrior can still use its 30 mm gun to de-track charging enemy tank and instantly destroy it with side shot or ATGM, but it's not very likely that the Warrior will live that long.

Also, in a worst-case scenario, the 30 mm autocannon can be used to try and shoot down planes with it, but it will require skill with slow-firing SPAA (like the Crusader AA MK I), and any plane coming down at a high angle can't be engaged.

Not convinced? The main gun can still remove any trees and solid fences at any range, which is normally a nightmare for any other British ATGM vehicle.

30 mm L21A1
Capacity (Belt capacity)		Fire rate (shots/minute)	Vertical guidance	Horizontal guidance	Stabilizer
222 (6)		81	-10°/+45°	±180°	N/A
Turret rotation speed (°/s)
Mode	Stock	Upgraded	Prior + Full crew	Prior + Expert qualif.	Prior + Ace qualif.
Arcade	57.1	79.06	96.0	106.16	112.94
Realistic	35.7	42.0	51.0	56.4	60.0
Reloading rate (seconds)
Stock	Prior + Full crew	Prior + Expert qualif.	Prior + Ace qualif.
1.30	1.15	1.06	1.0

Ammunition

Penetration statistics
Ammunition	Type of warhead	Penetration in mm @ 0°/60°
		10m	100m	500m	1000m	1500m	2000m
Default	AP-I/HEI-T*	52/26	50/25	39/20	29/14	21/11	16/8
30x170 APDS-T	APDS	110/42	101/39	95/36	69/26	52/20	41/16

Belt types

Belts	Shell composition	Combat usage
Default	AP-I, HEI-T (Armor Piercing Incendiary), (High-explosive incendiary-tracer) shells	This belt can be used against other light tanks and certain lightly armoured medium tanks. However, it also includes anti-air round (HEI-T), which does increase damage to air targets but is useless against tanks at rank 5. The low rate of fire of Warrior doesn't compliment this dual belt.
30x170 APDS-T	APDS (Armor piercing discarding sabot) shells	This belt can be used against sides of most medium tanks of rank 5 and 6, and even some heavy tanks can be damaged by it. Performance of this belt deteriorates much slower than of AP-I belt, but it does less damage the more armour it had to penetrate, resulting in an inability to set off enemy ammo racks in 1 hit if it was behind any good armour. If used against planes, it can damage or rip off wings, or snipe out the pilot.

Ammo racks

Full ammo	1st rack empty	2nd rack empty	3rd rack empty	4th rack empty	Visual discrepancy
XX	XX (+XX)	XX (+XX)	XX (+XX)	XX (+XX)

Turret empty: 62 (+3)
Front empty: 33 (+32)

Additional armament

Warrior carries MILAN missiles as a secondary weapon, although these function more as the primary armament due to the tank based gameplay in Warthunder.

Warrior managed to launch MILAN 2 straight at the enemy tank, instantly destroying it.

MILAN 1 has 500mm of RHA penetration. It is 103mm

MILAN launcher can be upgraded to the MILAN 2, which has 730 mm of RHA penetration. The MILAN 2 is 115mm. The flight performance is essentially the same.

The MILAN can be used at close ranges, but cannot be fired point-blank (10 m or so), and if not careful it can overshoot (look at launcher itself in Third-person view to avoid this). The missile only has 2km of range so it is not particularly useful against enemies at very long range, or more often against helicopters who are hovering far away from the battlefield.

103 mm MILAN ATGM
Capacity			Vertical guidance	Flight speed on launch (m/s)	Max Flight speed (m/s)	Range (m)
8			N/A	~160	200	2,000
115 mm MILAN 2 ATGM
Capacity			Vertical guidance	Flight speed on launch (m/s)	Max Flight speed (m/s)	Range (m)
8			N/A	~200	200	2,000

• Despite being launched at their max speed, they are still very manoeuvrable, so they still can be curved behind some hills at targets ~500 meters away, and generally targets up to 800 meters can't dodge it.

Ammunition

Penetration statistics
Ammunition	Type of warhead	Penetration in mm @ 90°
		10m	100m	500m	1000m	1500m	2000m
MILAN	ATGM	580	580	580	580	580	580
MILAN 2	ATGM	730	730	730	730	730	730

Shell details
Ammunition	Type of warhead	Velocity in m/s	Projectile Mass in kg	Fuse delay in m:	Fuse sensitivity in mm:	Explosive Mass in g (TNT equivalent):	Normalization At 30° from horizontal:	Ricochet:
								0%	50%	100%
MILAN	ATGM	200	6.6	0.0	0.1	1,400	+0°	80°	82°	90°
MILAN	ATGM	200	7.0	0.0	0.1	1,800	+0°	80°	82°	90°

Ammo racks

Full ammo	1st rack empty	2nd rack empty	3rd rack empty	Visual discrepancy
8	XX (+XX)	XX (+XX)	XX (+XX)

Optics and night vision

Warrior Optics
Type of optic	Magnification	Night Vision Devices
		Image Intensifier			Thermal Imager Resolution	Notes
		Resolution	Light Mult	Noise Level
Gunner's Sight	X~7 - X8	N/A	N/A	N/A	500x300	Only useable with tier 4 upgrade
Commander's View	X6	800X600	?	high	Not Fitted	Only useable with tier 4 upgrade
Driver's View	X1 / 3PV	800X600	?	high	Not Fitted	Only useable with tier 4 upgrade

• Zoom level estimated using optics gallery. Maximum zoom specified in X-ray. Comparable with TAM and many other light tanks.

The zoom is fixed to be only slightly higher than commander binoculars, which makes the use of it less important.

If commander optics (the ones on top of the turret) get destroyed, warrior cannot launch ATGM anymore. They can only be repaired via "manual repair".

After researching the NVD upgrade, a thermal scope of a gunner can be used to find enemy tanks, or to see if anything can block your ATGM on a way to the target. Be aware, as long as you press "go forward" the smoke and heat from exhaust on your right will prevent you from seeing anything throught thermal scope, so let go of the gas, when trying to look right.

Machine guns

The machine gun is kind of useless for Warrior, but it can still destroy weak fences, which normally slows any tank down if they hit them, and it makes much less noise than the main gun. For enemy marking purposes, Scouting should be used instead, as it doesn't reveal the vehicle.

7.62 mm L94A1
Coaxial mount
Capacity (Belt capacity)				Fire rate (shots/minute)	Vertical guidance	Horizontal guidance
2,000 (2,00)				600	N/A	N/A

Usage in battles

Generally, Warrior needs to quickly get into the medium range of the expected enemy, then figure out its strategy for the current battle. While moving towards an objective, Warrior should keep a low profile and scout every enemy it can notice.

After looking around, Warrior either takes some hills or well-protected hull-down position near to capture point to utilize ATGMs and scouting ability for medium-range attacks and team support, or takes an aggressive approach and goes for stealthy flanks and close-range combat. It's not rare to see Warrior try and destroy heavy tanks, which just don't expect the light tank to go at them.

If forced, Warrior can always use a smokescreen to disrupt enemy plans of taking it down, either baiting them to waste time looking for it, or using smokescreen, MILAN-2, scouting and add-on armour together to attack the enemy from the fog with little fear of being punished for it. For some reason enemy does not often reply to ATGM shots but instantly fires back at cannon fire, so use cannon sparingly during this.

Example of using smokes and armour offensively in arcade battle. Not only enemy is blinded and can't hold the line, allowing the team to rush in, but even if they fire towards the Warrior's general direction, they will likely load HESH and fire at the hull, hitting the add-on armour and doing no damage. MILAN-2, on the other hand, is almost unblockable and does fatal damage, and the player can clearly see the direction they are in due to scouting. A skilled Warrior can take out up to 2 tanks per 1 smoke deploy like that. Works on any range from 30m to 800m.

In any mode, but especially in AB, mark the enemy with the "scout" ability, so they can be found whenever smoke is deployed. This must be done for two main reasons:

1. Since the MILAN ATGM can instantly destroy or cripple anything, even seeing just the name of enemy and type of tank through smoke is good enough for the Warrior to have a chance for a hit. In realistic battles, it's less reliable, but the Warrior can still see where the enemy is. For light tanks, the 30 mm autocannon can work just fine (just don't do that against BMP; unless it already spotted and scouted the Warrior, it's not worth it).
2. In Arcade Battles, If the "intelligence" reward is obtained for marking enemy that was or is invisible to teammates and then got destroyed, the player will get artillery support point and airstrike point. If the squadmates destroys the marked target, the player will get airstrike point regardless as a squad assist.

Due to this, in 9.0 arcade battle warrior can call in ATGM helicopters on very first minute of a fight, simply by marking 2 enemy vehicles and destroying someone with an almost undodgeable and unblockable missile, while the enemy cannot even request gunships to protect themselves from it. ATGM helicopter than can destroy 6 to 10 enemy tanks, significantly weakening the enemy team. As the game goes on, Warrior can join multiple air battles in a row as second attack helicopter or bomber, because it's a scout vehicle.

Since MILAN has relatively good controls and there is 8 missiles total, the Warrior can try and fire it above hills and guide it down on people, much like Swingfire and Striker. It's harder to aim at the enemy without a straight visual firing line, but if it hits anywhere important, they could be knocked out anyway. Since the Warrior is considered a scout vehicle, mark them and ping them on the map, even if a shot lands a hit.

In Arcade Battles (AB), it's best to fire the missile at tank's gunner, so in case if it didn't destroy the tank on its own, the Warrior can just circle around the enemy and use the main gun to destroy the engine, then proceed to incapacitate the crew. In Realistic battles (RB) even taking out cannon barrel or breach might be enough, as repairs in that mode take much more time, and field repair doesn't even guarantee, that gun won't just jam itself again or fire in a completely different direction.

As with all light tanks play style, be very wary of people that have any kind of explosive ammo, as the Warrior has the Hull Break mechanism on it and can be easily engaged. With Add-on armour, the Warrior can fight them directly, but the vehicle's turret, front and back are still a giant weak spot.

Usually, MBT's will carry AP ammo as their first shot, which may just over-penetrate and maybe do almost nothing. So if there is an absolute must directly attack someone, attack them, SPGs or other non-Soviet light tanks.

There is also a trick related to the Warrior - if baiting an enemy that is looking towards the Warrior, pull the Warrior's rear end out of cover first. Since the rear has very little critical components outside of the MILAN missile stowage, usually being shot there doesn't do anything too drastic for the overall tank health. After being fired at, drive out of cover and fire back at them. This trick probably won't work twice, indicating you should make the most out of the opportunity you have at hand. Nobody likes to be shot with ATGMs and the second shot coming will most certainly be HE of some kind. This tactic may backfire if your IFV gets shot with APHE, or APDSFS will enter the vehicle at a bad angle, but those types of ammunition have the potential of instantly destroying Warrior regardless of the entry point.

Finally, the Warrior can also repair any allies, so if in cover and not busy - do help them.

Specific enemies worth noting

Any Soviet light tanks: Destroy it with ATGM, use scout ability to see when they are trying to leave their cover, use gun adjustment to never miss, generally never play around with them. BMP-1 will just hull break the Warrior, BMP-2 will just turn on full auto mode and unload half of its magazine into its target, even if it misses its ATGM, just to get rid of a threat and even add-on armour won't save the Warrior at that point. Oddly enough, the infamous Object 906 is probably the least dangerous of them, but it will still destroy the Warrior with proper shot placements. If the Warrior is spaded in modifications, just call artillery strike on them.

IS-7: Do not ever engage this thing frontally without MILAN 2 and add-on armour. It is also extremely risky to attack it on a narrow street. Fire at the right (their left) side, to disable its turret. The main goal in engaging this tank is to disable its engine with the 30 mm gun and then blow it up by destroying its ammo in back of a turret or just blowing it up by firing ATGM in the middle of it or into ammo rack, if there is a spare ATGM (the IS-7, as a threat to any BR below 8.0, should be prioritized with every missile in the Warrior's capacity). Even the many machine guns on the IS-7 can shred the Warrior apart.

Any tank with heavy machine guns: If possessing the add-on armour modification, simply avoid turning the rear towards them, otherwise the weak rear armour would be easily penetrated. Weaker machine guns of around 7.62 mm calibre can't penetrate the Warrior armour at all, and even 14,5 mm will have some problems penetrating the front of the hull and protected sides, so just destroy them by returning cannon fire and avoiding being hit in the turret. They'll never see it coming.

Counter-tactics

Just fire at its turret, preferably with explosives or high fire rate guns.

If it tries to spook away a threat by being ominous and peeking over hills, disable its ATGM camera (on "ears") with concentrated fire if a direct hit to the crew and modules is not possible. Keep in mind that must damage whole IFV really hard for ATGM repairs to take long (otherwise it may take less than rearm time, which is not good). If the missile is already homing towards a vehicle with no way to break visual, try to get outside of direct missile control range (which will make missile spiral crazily and possibly missing by a centimetre) or face it with the gun barrel in hopes that it would absorb the damage and not cripple any critical modules.

Never fire pure AP rounds to the back of this tank, since unless it hits one of the missile ammo racks there, it will just do nothing to it.

If the Warrior has the add-on armour package, do not underestimate it and use anything possible when engaging it, not just HMG. Warrior repairs and reloads fast enough to disable its adversaries, if it must, just set it on fire is not going to stop it. Low calibre machine guns are useless against hull from front, despite it having incomplete add-on armour protection.

In case Warrior destroyed your primary weapon, but you still have 12.7 mm machinegun, you can fire at its ventilation to destroy it. It's very well hidden on the right-front side of the IFV (left for you, if facing it) behind a small grey shield, making it nearly unnoticeable. Firing at ventilation from the side is also possible, but it will do less than fatal damage.

The Warrior can be destroyed by a fighter jet. However, do not just strafe it directly, as it actually can fire back and may have armour. It's best to attack it from the top.

Modules

Tier	Mobility		Protection	Firepower
I	Tracks		Parts	Horizontal Drive	30x170 APDS-T
II	Suspension	Brake System	FPE	Adjustment of Fire	Airstrike
III	Filters		Crew Replenishment	Elevation Mechanism	MILAN 2
IV	Transmission	Engine	Additional Protection Package	Artillery Support	Improved Optics	NVD

Pros and cons

Pros:

• Extremely powerful ATGM with 8 missiles
• Can stop pushes if manages to get to good cover
• Can survive a direct hit by a miracle and even brawl with MBT's if armour mod is installed
• First of the only British light tanks beyond rank 1 (aside from the rare exception being rank II AEC Mk.II), the other one one being Rooikat Mk.1D, meaning British players are now able to use scouting mechanics
• Has gunner thermal (2nd generation) vision and commander / driver night vision

Cons:

• Can be destroyed by other light tanks easily, especially if situation awareness is not maintained
• Any properly landed turret shot will destroy the vehicle, with nearly no way to survive if it was a HE shell
• Many will be disheartened by the main gun's performance, especially in a duel with other light tanks
• Add-on armour does less than one may expect from it, it's not clear when the Warrior survived a hit by sheer luck or because of armour plates.
• Engine exhaust placement (front right corner of tank) means that hot exhaust fumes obscure gunners thermal vision when looking between approximately 45° and 80° to the right.

History

The FV510 infantry fighting vehicle was developed as part of a program to create a modern IFV for the British army at the end of the ’70s. The vehicle went into series production in 1986. The vehicle was equipped with 30 mm gun, fed by magazines of three shells each. This gun was designed to destroy lightly armoured vehicles with maximum accuracy. For the Desert Storm operation, the Warriors were equipped with Chobham passive armour – add-on armour plates that significantly improved the IFV’s defence in battle, allowing it to survive a hit from an RPG-7 grenade and shrapnel from high-calibre HE rounds. A little later, in 1990, the military decided to equip the Warrior with anti-tank weaponry – a 30 mm gun for these targets was clearly not enough. The roof of the turret was equipped with a launcher for the MILAN ATGM. The commander used a hatch to fire the ATGM, and it was reloaded through the upper hatch of the armoured vehicle’s infantry compartment. The FV510 Warrior is still in service with the British army and is the main IFV of the United Kingdom.

- From Devblog

Media

The Shooting Range #116 - Metal Beasts section at 00:35 discusses the Warrior.

Confusion and destruction tactics with the Warrior.

PhyDaily - Warrior gameplay in Realistic Battle

See also

Links to the articles on the War Thunder Wiki that you think will be useful for the reader, for example:

• reference to the series of the vehicles;
• links to approximate analogues of other nations and research trees.

External links

• [Devblog] FV510 Warrior: Built for the future!