3D models for aircraft - Revision history

U168239580: added parachute emitter as it was left out and important for modern aircraft.

2024-06-09T09:39:32Z

added parachute emitter as it was left out and important for modern aircraft.

U168239580: removed extra reference to canopy parts and added radar to damage model table

2024-05-29T05:41:22Z

removed extra reference to canopy parts and added radar to damage model table

U168239580: Added canopy and extra elevon parts to damage model and normal model areas

2024-05-29T05:36:05Z

Added canopy and extra elevon parts to damage model and normal model areas

U168239580: Added elevons to the list of available model parts, fixed minor spelling and logic mistakes.

2024-05-21T06:12:21Z

Added elevons to the list of available model parts, fixed minor spelling and logic mistakes.

U168239580: added elevons to part list (very helpful for delta wing modelling)

2024-03-29T16:19:19Z

added elevons to part list (very helpful for delta wing modelling)

U78314945: fixed typo in terminology and added aileron aircraft part to the table

2024-03-08T10:43:27Z

fixed typo in terminology and added aileron aircraft part to the table

Show changes

U3312106: /* Model */ Updated using info from the RU wiki which has more accurate values (according to NovA29R, the person who makes 3d models and most of them were added to the game, IAR 81 etc.)

2020-12-26T07:55:36Z

‎Model: Updated using info from the RU wiki which has more accurate values (according to NovA29R, the person who makes 3d models and most of them were added to the game, IAR 81 etc.)

U28580205: Changed protection level for "3D models for aircraft" ([Edit=Allow only autoconfirmed users] (indefinite) [Move=Allow only autoconfirmed users] (indefinite))

2019-02-05T16:50:47Z

Changed protection level for "3D models for aircraft" ([Edit=Allow only autoconfirmed users] (indefinite) [Move=Allow only autoconfirmed users] (indefinite))

U28580205: Protected "3D models for aircraft" ([Edit=Allow only administrators and moderators] (indefinite) [Move=Allow only administrators and moderators] (indefinite))

2019-02-05T16:35:22Z

Protected "3D models for aircraft" ([Edit=Allow only administrators and moderators] (indefinite) [Move=Allow only administrators and moderators] (indefinite))

U36063762: /* Download the guide */

2018-09-01T10:35:07Z

‎Download the guide

@@ Line 546: / Line 546: @@
 * '''emtr_exhaust#''' – engine exhaust effects. Placed at the ends of exhaust pipes (end of jet nozzle)
 * '''emtr_oil#''' – oil leak, oil burn effects. Placed inside of oil radiators
 * '''emtr_fuel#''' – fuel leak, fuel burn effects. Placed on the surface of fuel tanks. Please see aircraft x-ray layout for fuel tank positions. Each fuel tank must have an emitter
 * '''emtr_engine#''' – damaged engine on fire effects
@@ Line 669: / Line 670: @@
 === Normal and Specular Texture ===
 [[file:wiki_normal_and_specular.png|300px|thumb|left|]]
@@ Line 674: / Line 676: @@
 The normal map and specular maps are the same size as primary diffuse texture. Normal map uses RGB channels and Specular map uses an alpha channel. Normal maps in layered source files should be present as height maps before the NormalMapFilter conversion. Converted (blue) normal maps in layers are used for minor corrections only.
 Use filter default settings for height to normal map conversion: Min Z = 0, Scale = 8.
@@ Line 766: / Line 769: @@
 [[File:Wiki dmg overlaps.png|350px|thumbnail|left|Figure 50: Left-image, incorrect. Right-image, correct.]]
@@ Line 959: / Line 965: @@
 |-
 | elevator#_dm (0 to 2) || double/triple elevator config
 |-
 | rudder_dm || primary rudder part (single rudder config)
@@ Line 991: / Line 985: @@
 |-
 | gun#_dm (1 to 12) || turret gun
 |-
 |-
@@ Line 1,144: / Line 1,132: @@
 Right below the animation range are thresholds for key optimizations during export. Most notably the position “~pos:” and rotation “~rot:” thresholds are important. Position is measured in your current system units. Rotation is measured in degrees. These values show the amount of change necessary to save out a key if there is one.
 Default values are used most of the times. If you have undesired animation behaviour in the exported model you may try to lower these values.

@@ Line 401: / Line 401: @@
 |-
 | Additional jet flame objects (for aircraft with more than 1 engine)|| jet_flame#
 |-
 |-
@@ Line 672: / Line 669: @@
 === Normal and Specular Texture ===
 [[file:wiki_normal_and_specular.png|300px|thumb|left|]]
@@ Line 678: / Line 674: @@
 The normal map and specular maps are the same size as primary diffuse texture. Normal map uses RGB channels and Specular map uses an alpha channel. Normal maps in layered source files should be present as height maps before the NormalMapFilter conversion. Converted (blue) normal maps in layers are used for minor corrections only.
 Use filter default settings for height to normal map conversion: Min Z = 0, Scale = 8.
@@ Line 771: / Line 766: @@
 [[File:Wiki dmg overlaps.png|350px|thumbnail|left|Figure 50: Left-image, incorrect. Right-image, correct.]]
@@ Line 1,002: / Line 994: @@
 |blister#_dm (1 to 4)
 |canopy parts
 |-
 |-
@@ Line 1,149: / Line 1,144: @@
 Right below the animation range are thresholds for key optimizations during export. Most notably the position “~pos:” and rotation “~rot:” thresholds are important. Position is measured in your current system units. Rotation is measured in degrees. These values show the amount of change necessary to save out a key if there is one.
 Default values are used most of the times. If you have undesired animation behaviour in the exported model you may try to lower these values.

@@ Line 401: / Line 401: @@
 |-
 | Additional jet flame objects (for aircraft with more than 1 engine)|| jet_flame#
 |-
 |-
@@ Line 669: / Line 672: @@
 === Normal and Specular Texture ===
 [[file:wiki_normal_and_specular.png|300px|thumb|left|]]
@@ Line 676: / Line 678: @@
 The normal map and specular maps are the same size as primary diffuse texture. Normal map uses RGB channels and Specular map uses an alpha channel. Normal maps in layered source files should be present as height maps before the NormalMapFilter conversion. Converted (blue) normal maps in layers are used for minor corrections only.
 Use filter default settings for height to normal map conversion: Min Z = 0, Scale = 8.
@@ Line 770: / Line 771: @@
 [[File:Wiki dmg overlaps.png|350px|thumbnail|left|Figure 50: Left-image, incorrect. Right-image, correct.]]
@@ Line 970: / Line 967: @@
 |-
 | elevator#_dm (0 to 2) || double/triple elevator config
 |-
 | rudder_dm || primary rudder part (single rudder config)
@@ Line 990: / Line 999: @@
 |-
 | gun#_dm (1 to 12) || turret gun
 |-
 |-
@@ Line 1,137: / Line 1,149: @@
 Right below the animation range are thresholds for key optimizations during export. Most notably the position “~pos:” and rotation “~rot:” thresholds are important. Position is measured in your current system units. Rotation is measured in degrees. These values show the amount of change necessary to save out a key if there is one.
 Default values are used most of the times. If you have undesired animation behaviour in the exported model you may try to lower these values.

@@ Line 314: / Line 314: @@
 | Left Rudder || rudder0 *
 |-
-| Right Rudder || rudder2 *
+| Right Rudder || rudder1 *
 |-
 | Elevator || elevator
@@ Line 326: / Line 326: @@
 |-
 |Additional Left Elevons
-|elevon#_r
+|elevon#_l
 |-
 |Right Elevon
@@ Line 334: / Line 334: @@
 |elevon#_r
 |-
-| Left slat || lat_l
+| Left slat || slat_l
 |-
 | Right slat || slat_r

@@ Line 322: / Line 322: @@
 | Right elevator || elevator1 *
 |-
-|Left aileron
+|Left Elevon
-|ailerons_l
+|elevon_l
 |-
-|Right aileron
+|Additional Left Elevons
-|ailerons_r
+|elevon#_r
 |-
-| Left slat || slat_l
+|Right Elevon
 |-
 | Right slat || slat_r

@@ Line 58: / Line 58: @@
 The figures below are recommended:
 For complex models overhead of 5-10k is allowed.
-*LOD0 – around 50-70k triangles for fighters and 60-100k for bombers
+*LOD0 – around 50-150k triangles for fighters and 60-250k for bombers
 *LOD1 – around 15-23k tris for fighters and 18-33k tris for bombers
 *LOD2 – around 1,500-2,000 tris
@@ Line 64: / Line 64: @@
 When making LODs bear in mind that LOD switching has to be smooth and the model should look good at certain distances.
 Here are the LOD visibility distances:
-*LOD0 – 0 to 150 meters
+*LOD0 – 0 to 70 meters
-*LOD1 – 150 to 500 meters
+*LOD1 – 70 to 200 meters
-*LOD2 – 500 to 1,000 meters
+*LOD2 – 200 to 550 meters
-*LOD3 – 1,000+ meters
+*LOD3 – 550+ meters
 at 90 degree FOV.

← Older revision	Revision as of 16:50, 5 February 2019
(No difference)

← Older revision	Revision as of 16:35, 5 February 2019
(No difference)

← Older revision		Revision as of 10:35, 1 September 2018
Line 1,121:		Line 1,121:

	[[Category:War Thunder CDK]]		[[Category:War Thunder CDK]]
−	[[Category:~~Game_mechanics~~]]	+	[[Category:Custom aircraft models]]